Selection of a drill according to the geological conditions

 use single bottom of auger core drilling bit bucket, if the diameter is too small can or bucket with dumping soil clovenfooted board core drilling bit bucket. 2, mud, sticky soil is not strong, sand, cement poor gravel layer smaller particle size, can be equipped with a double bottom core drilling biting core drilling bit bucket. 3, hard clay: use a single port into the soil (single double bottom can) auger core drilling bit bucket, bucket teeth straight or spiral. 4, permafrost: less available ice bucket teeth straight auger hopper and auger core drilling bit bucket, can be large cone ice auger, a description that auger for soil (except silt outside) are valid, but there must be no use of groundwater in the case, in order to avoid the suction effect caused by stuck. 5, cemented gravel and strongly weathered rock: be equipped with a conical double bottom auger and auger core drilling bit bucket (large diameter single-port, dual-port with a small particle size) 6, stroke bedrock: drum cutter with coring core drilling bit - Tapered auger - rotary core Drilling Tools bucket digging double bottom, straight or spiral cutter core drilling bit - rotary core drilling bit bucket digging double bottom. 7. breeze bedrock: with cone core drilling bit coring barrel - conical auger - Rotary core drills bits bucket digging double bottom should be taken if the diameter is too large grade core drilling biting process.

Drum core drill

At present, there are two common: tube cutter drill (for medium hard rock and gravel), core drill bits tube (for hard rock and large boulders). In barrel coring drill bit in two categories, and with and without coring device to take points of core devices, depending on the difficulty of coring. Because cone core drill is mainly used for hard rock drilling and drill the ring area, if the conditions can also pass on part in the installation of reverse circulation core drill bit to improve drilling efficiency. 4, belled pile diameter drill bit does not increase without increasing deep foundation piles, in order to improve the bearing capacity of single pile, the design department is often achieved through the pedestal pile, rotary drilling rig construction is expanding bottom without any changes can be construction just choose belled drill can be. Belled drill used to mechanically based, such drills are relatively simple to use and maintain, there is the open and under the open, the opening of the four-link mechanism is generally used for soil, strong winds, weathered even hard rock formations. Due to non-circulation drilling Rotary core drills bits, completion of expansion after the end of the barrel with slag slag can be.

The classification of core drill bits

Rotary core drill biting rig construction of the strata vary, technical requirements and different, just by selecting different core drill bits to meet various construction requirements, so do the matching rotary core drill biting rig core drill bit work is very important. Impact rotary core drill biting rig core drill bit matching many factors, summed up in three aspects: stratigraphy; rig functions; hole depth, the specific requirements of the aperture, Shen ballast thickness Wall measures. First, the current classification of common auger core drill bit bit common spiral auger core drill bit, rotary bucket, drum core core drill bit, core drill bit belled, GRABBING cone core drill bit and hydraulic grabs, following a brief introduction by the class. 1, the auger (1) cone: Double double spiral for hard rock. Double single screw for weathered bedrock, gravel, soil, etc. containing ice. Equipped with a variety of the above core drill bit cutter through tooth pitch, helix angle of the change can be derived from the many types of core drill bits. (2) straight auger: bucket teeth straight Lo: Double double spiral, suitable for sand, cement poor small-diameter gravel; single-headed screw, suitable for sand, soil; single head single screw for poor cementation large diameter gravel, clay soil and hard clay. Straight screw cutter: a double spiral, three and four-Lo Lo, then apply hard rock or gravel. 2, auger core drilling bit bucket teeth can be divided by the installed cutter core drill bit bucket and bucket teeth core drill bit bucket; the floor can be divided according to the number of double bottom bucket and single bottom bucket; can be divided according to the number of open double doors and single bucket open bucket; can be divided according to taper cone barrels barrels barrels of core drill biting straight core drill bit bucket and bucket; can be divided according to the lower plate shaped pot bottom of the core drill bit core drill bit bucket peaceful struggle. Above structure combined with each other, plus whether vented, change door mechanism can be combined dozens of auger core drill bit bucket. Generally applicable double bottom formation core drills bits bucket wide range, single bottom applies only to tack a strong soil, two-door core drill bit formations suitable for a wide range of fighting, fighting only for single door core drill bit large diameter and pebbles hard clay.

The function of core drill bit

The rotary core drill bitsing rig features to choose if the auger core drill bits bit has to do a continuous function, can be equipped with hydraulic grab or continuous milling wheel construction. If the secondary rope winch with automatic release function, optional percussion core drill bits bit and core drill bits large diameter core drill bits  GRABBING pebbles or boulders. If equipped with gas chambers and faucets can be gas-liquid core drill bits. If equipped with dual power head or rub into the casing pipe core drill bit machine can be, which is to solve the flow of sand, crushed gravel, silt layer effective construction method.according to the choice of a number of other factors core drill bits if Shen ballast thickness requirements more stringent or belled during core drill bitsing, the need to fight with dedicated clean ballast. When core drill bits into the sleeves, a small gap between the core drill bits and the casing, in order to prevent and reduce the core drilling bits casing hanging touch suction effect, matching the core drill bits should have vent, with the core drill bits bit with a guide, opening and closing device as close to the center of the core drill bits, one of the best machine hand. You can also solve this problem through the use of special combination core drill bits.

Selection of core drill according to the geological conditions

   Rotary core drill biting rig main function is to form a hole in the ground tank, work object is a rock pile hole depth due to the construction of shallow rock through tectonic movement, the role of mechanical and chemical nature, structure, grain size, porosity, bond conditions , occurrence, strength and other complex changes occur, coupled with our vast pieces of the original, so the object of rotary Arix core drill bit rig work is particularly complex. Summed up in the following categories. By lithology points (common) for shale, sandstone, limestone, granite; divided by cause magmatic rocks, sedimentary, metamorphic; divided by the mechanical properties of sturdy plastic and loose. So how to choose based on stratigraphy core drill bit it? The following classification of introduction. (1) Clay: use single bottom of auger core drill bit bucket, if the diameter is too small can or bucket with two removable panels earth core drill bit bucket. (2) slurries, viscous not strong soil, sand, cement poor gravel layer smaller particle size, can be equipped with a double bottom core drill biting core drill bit bucket. (3) hard clay: use a single port into the soil (single double bottom can) auger core drill bit bucket, bucket teeth straight or spiral. (4) the permafrost: a small amount of available ice bucket teeth straight auger hopper and auger core drill bit bucket, available in large cone ice auger, a description that auger for soil (except silt outside) are valid, but there must be no use of groundwater in the case, in order to avoid the suction effect caused stuck. (5) cemented gravel and strongly weathered rock: be equipped with a conical double bottom auger and auger Diamond Core Drill Machine bucket (large diameter single-port, dual-port with a small particle size) (6) stroke group rock: drum cutter with coring core drill bit - tapered auger - spin double bottom bucket digging core drill bit or auger cutter straight - rotary core drill bit bucket digging double bottom. (7) weathered bedrock: with a cone core drill bit coring barrel - conical auger - Rotary core drill bit bucket digging double bottom should be taken if the diameter is too large grade core drill biting process.

Drum core drill bit

At present, there are two common: tube cutter drill (for medium hard rock and gravel), core drill bit tube (for hard rock and large boulders). In barrel coring drill bit in two categories, and with and without coring device to take points of core devices, depending on the difficulty of coring. Because cone core drill is mainly used for hard rock drilling and drill the ring area, if the conditions can also pass on part in the installation of reverse circulation core drills bits drill to improve drilling efficiency. 1,4 expanding bottom pile diameter drill in deep pile does not increase without increasing basis, in order to improve the bearing capacity of single pile, the design department is often achieved through the pedestal pile, rotary drilling rig construction is expanding bottom without any changes can be construction, you can simply choose belled core drilling bits. Belled drill used to mechanically based, such drills are relatively simple to use and maintain, there is the open and under the open, the opening of the four-link mechanism is generally used for soil, strong winds, weathered even hard rock formations. Due to non-circulation drilling Rotary Drilling, completion of expansion after the end of the barrel with slag slag can be.

The classification of core drilling bits

Current common classification auger core drilling bits common helical auger core drilling bits, rotary bucket, drum core drilling bits, belled core drilling bits, impact core drilling bits, red cone core drilling bits and hydraulic grab grab, following a brief introduction by the class. 1,1 auger (1) cone: Double double spiral, suitable for hard rock. Double single screw for weathered bedrock, gravel, soil, etc. containing ice. Equipped with a variety of the above core drilling bits cutter through tooth pitch, helix angle of the change can be derived from the many types of core drilling bitss. (2) straight auger: a, bucket teeth straight Lo: Double double spiral, suitable for sand, cement poor small-diameter gravel; single-headed screw, suitable for sand, soil; single head single screw, suitable for large diameter difference cemented gravel, clay soil and hard clay. b, picks straight spiral: a double spiral, three and four-Lo Lo, then apply hard rock or gravel. 1,2 auger core drilling bits bucket teeth can be divided by the installed cutter core drilling bits bucket and bucket teeth core drilling bits bucket; the floor can be divided according to the number of double bottom bucket and single bottom bucket; can be divided according to the number of open double doors and fighting single door bucket; can be divided according to taper cone barrel barrel barrel core drill bit bucket and core drilling bits straight fight; shape can be divided according to the lower plate and flat-bottom pot core drilling bits bucket core drilling bits bucket. Above structure combined with each other, plus whether vented, change door mechanism can be combined dozens of auger core drilling bits bucket. Generally applicable double bottom formation core drilling bits bucket wide range, single bottom applies only to tack a strong soil, two-door core drilling bits formations suitable for a wide range of fighting, fighting only for single door core drills bit large diameter and pebbles hard clay.

The application of core drill bits in oil industry

Oil diamond core drill bits for metal, a place where people both familiar and unfamiliar terms. Iron Man Wang Jinxi jumped into the mud pool is famous photograph; but into the automobile age, are inseparable from the era of oil per day, the iron man's back seems hidden in the river of time. In front of the lens and diamond core drill bit Taking this group and the case for people to expand the memory of the screen. The authors used industrial techniques of documentary photography exhibit "Machine + human" art, the subject matter is traditional and simple, and the lens is skillful sophisticated language, such as into nirvana. After years of oil creative photography, the authors would break something light 24-70mm lens 2. Regardless of hardships creation of diamond core drill bits, the most appropriate focal length documentary photography release a strong signal: return to the origin of photography. At the beginning of the invention of arix core drill bit, painting is to replace live recording, although the pictorial photography lyrical rage, but as the most direct visual language, enduring foundation for candid shots. Recent foreign academic debate "Straight Photography" The photography basic terms should be translated "direct photography" or "straight photography", there are people that such realism photography has become outdated.